Grippers

FoamGripper120x200mm, thin pattern, integrated vacuum generation, check valves

2-jaw self-centering servo-electric parallelgripperwith long stroke - MPLF Gimatic catalogue MPLF series

Grip strength: 78 N - 7,286 N
Stroke: 2 mm - 25 mm

2-jaw self-centering pneumatic parallelgripper• Double acting with optional springs (on closing or on opening). • Long stroke or short stroke. • Possibility of front fastening with through screws. • High efficiency ...

Pneumaticgrippersfrom the 6300 series are typically used in complex systems such as assembly machines, robots, manipulators etc. This series covers the wide range requirements of this sector, allowing a variety of applications.

... applications. The range includesgrippersequipped with holding fingers operating from -10° to +30° degrees, with 180° degree opening, or a parallel guidedgripperwith great rigidity throughout the stroke. The ...

Pneumaticgrippersfrom the 6300 series are typically used in complex systems such as assembly machines, robots, manipulators etc. This series covers the wide range requirements of this sector, allowing a variety of ...

Grip strength: 70, 170 N
Stroke: 5 mm

• Dual-acting parallelgripperfor internal and external clamping. • Anodized aluminium alloy body and tempered steel jaws. • Bottom or side fixing. • All sizes come with magnets and sensor slots Quantity per ...

Grip strength: 170, 70 N
Stroke: 5 mm

Dual-actinggripperswith parallel jaws and internal and external clamping. The body is made of anodized aluminium alloy and the jaws are made of hardened steel. All sizes are equipped with a magnet and sensor grooves. ...

Grip strength: 135, 100, 45 N
Stroke: 5, 4, 7 mm

Double-acting system with clamping in both directions. All thegripperscome with magnet and sensor slots. Quantity per package: 0 Minimum order quantity: 0 Unit of measure: items Actuators: Handling bore (mm): ...

Grip strength: 250 N - 280 N
Stroke: 6 mm - 12 mm

... ~ 0.8 Operating Temperature (℃): 5 ~ 60 Note 1. Please install a check valve in the air-pressure circuit so that thegripperwill not release a workpiece even if the air pressure drops down. Note 2. A reed switch ...

Grip strength: 750 N - 800 N
Stroke: 6 mm - 12 mm

... ~ 0.8 Operating Temperature (℃): 5 ~ 60 Note 1. Please install a check valve in the air-pressure circuit so that thegripperwill not release a workpiece even if the air pressure drops down. Note 2. A reed switch ...

Grip strength: 500 N - 600 N
Stroke: 8.3 mm - 16.6 mm

Thin 2-jaw parallelgripperThe thin body enables flexible system design The high restoration accuracy by utilizing workholding technology of lathe chucks NPGT achieves higher gripping force than the similar stroke ...

Grip strength: 28 N - 1,082 N
Stroke: 41 mm

... light and resilient Our self-centering, parallelgripperswith an H-shaped guide are available in 5 sizes with standard or long stroke. Because of the materials and surface coating used, thegripper...

Grip strength: 36, 60, 84, 144 N

... control. The Series CGSPgrippers, available in 4 sizes (20, 25, 32 and 40) are parallel and double-acting, self-centering and guided by means of a T-shaped sliding guide. Thanks to the materials and surface coating ...

The CGSN Series offers angulargrippersthat are designed to operate at 1 bar/7 bar pressure, 100 cycles/min. maximum frequency and -10°C/60°C temperature in dual effect. Thesegripperscan work continuously ...

OCTOPUS vacuum gripping bars These bars have been created to further facilitate the installation of OCTOPUS vacuum gripping systems on palletising robots. They are based on the same operating principle and, in addition to the advantages ...

... rating suitable for using longgripperfingers - Monitoring with electronic magnetic switches for a maximized process reliability - Mounting from two sides in four screw directions for universal and flexible ...

Grip strength: 123 N - 21,150 N
Stroke: 2 mm - 45 mm

... maximum moments possible suitable for using longgripperfingers Drive concept oval piston for maximum gripping forces Mounting from two sides in three screw directions for universal and flexiblegripper...

Grip strength: 180 N - 8,750 N
Stroke: 2 µm - 25 µm

Description Universal 2-finger parallelgripperwith permanent lubrication, high gripping force, and high maximum moments due to the use of a multi-tooth guidance. Field of application Pneumatic universalgripper...

Grip strength: 140 N - 26,050 N
Stroke: 2 mm - 45 mm

... Leakproof and corrosion protected – The universalgripperSuitable for virtually all ambient conditions, with a sealed guide up to IP67 and corrosion protection as standard, you are able to use thisgripper...

Grip strength: 6 N - 400 N
Stroke: 1 mm - 12 mm

... benchmark Optimisation of weight and force reduces your application costs since all components can have a smaller scale • -Gripperjaws up to 50% longer than the benchmark The highest force and torque measurement ...

Grip strength: 8.4 N - 5,250 N
Stroke: 3 mm - 13 mm

"The enduring" • - Proven technology We have more than 20 years of proven reliability, which ensures uninterrupted production for you • - Very short cycle times Low-friction circular guides enable very short cycle times and, therefore, ...

Grip strength: 1 kgf - 68 kgf

... than aluminum and offering mechanical strength 6 times greater . flexible material on thegripperedges, to protect bothgripperand operator . foam gripping interface, for versatile product handling . ...

Grip strength: 4 kgf - 60 kgf

... For example, for a PA 20clampwith the gripping point 25mm from the fulcrum, the clamping force will be: F = 10.1 (table below) x 15/25 = 6.06 kg. The weight of the objects to be handled is added to that of the ...

Grip strength: 600 N - 2,200 N

The CVGL series by Coval is a Vacuumgripperwhich features its flexible, simple and economic characteristic. The handling parts it contains comes with different sizes, shapes and weights. Using this tool, the user is ...

Grip strength: 150 N - 10,750 N
Stroke: 5 mm - 70 mm

Robust / 10 sizes Accuracy +/- 0.015mm Adjustable stroke IP rating 40 .... 65 Total stroke control Device to maintenance the gripping force Pressurization Versions up to 130 ° C

Grip strength: 123 N - 3,200 N
Stroke: 4 mm - 32 mm

便宜的一个djustable stroke Rating IP 40 Device to maintenance gripping force Pressurization Versions up to 130 ° C

Grip strength: 60, 100, 190 N
Stroke: 3, 6, 13 mm

2-finger parallelgripperExcellent stroke / gripping force ratioGripperfrom 80gr Stroke from 8 to 42 mm Rating IP 40 Device to maintenance gripping force Pressurization Versions up to 130 ° C

Grip strength: 208 N - 505 N
Stroke: 2, 4 mm

... round and angular workpieces with two parallelgripperfingers for handling with robots or portals. • High gripping force with low dead weight and compact design • High torque support for using longgripper...

Grip strength: 316 N - 932 N
Stroke: 3, 6 mm

... round and angular workpieces with two parallelgripperfingers for handling with robots or portals. • High gripping force with low dead weight and compact design • High torque support for using longgripper...

Grip strength: 470 N - 1,236 N
Stroke: 4, 8 mm

... round and angular workpieces with two parallelgripperfingers for handling with robots or portals. • High gripping force with low dead weight and compact design • High torque support for using longgripper...

Grip strength: 30 N - 550 N

... pneumatic angulargripperis developed by AVM Automation. It is equipped with two concentric fingers double effect. The opening angle of thisgripperis 90° per finger while the closing angle of thegripper...

Grip strength: 40 N - 340 N
Stroke: 3 mm - 20 mm

The Type 24 is a parallelgripperintegrated with two concentric fingers made available in 7 sizes mainly produced to handle several parts in any particular applications. It is also ideally designed with a magnetic piston ...

Grip strength: 40 N - 200 N
Stroke: 2 mm - 16 mm

... three jaw parallelgripperis developed by AVM Automation. It is equipped with three concentric fingers double effect. In addition, thegripperis being offered in three sized for handling of parts in ...

Screw action grips provide a very simple and efficient method for holding test specimens in a wide range of applications. The dual-acting design means that jaw faces can be adjusted to accommodate different specimen thicknesses, this ...

ADVANCED HYDRAULIC WEDGE ACTION GRIPS For Static and Dynamic Testing of Metals and Composites Advanced Hydraulic Wedge Action Grips are a versatile grip that can be used in both static and dynamic materials testing applications ...

Grip strength: 1, 2, 5 kN

拉伸测试薄片、电影、灵活的Plastics, Rubber, and Elastomers The self-tightening grips are primarily designed for the precision testing of elastomeric and other flexible materials exhibiting a large reduction in ...

Grip strength: 0 N - 10,000 N

... protection of specimens from unnecessary tensile or compression forces due to the materials flow or grip deformation when theclamp正在关闭。扣人心弦的一个之间的比率d tensile forces can be individually ...

Grip strength: 0 kN - 1 kN

The Pneumatic grips are suitable for various materials that are needed to be held. Their gripping force is generated specifically by pneumatic cylinders that act directly on the jaws or through a lever system. A separation of the tensile ...

Grip strength: 0.5 kN

These grips are primarily used for testing highly ductile plastics and elastomers. The pincer principle produces a strong increase in gripping force during the test.

Grip strength: 4.6 N - 4.6 N
Stroke: 30 mm - 36 mm

The SFG flexiblegripperis an innovative flexiblegripperthat imitates the starfish design and simulates human grasping. Realize bending deformation by inflating, cover the target object adaptively, ...

Grip strength: 8.5 N - 8.5 N
Stroke: 25 mm - 36 mm

The SFG flexiblegripperis an innovative flexiblegripperthat imitates the starfish design and simulates human grasping. Realize bending deformation by inflating, cover the target object adaptively, ...

The SFG flexiblegripperis an innovative flexiblegripperthat imitates the starfish design and simulates human grasping. Realize bending deformation by inflating, cover the target object adaptively, ...

Grip strength: 3 N - 40 N
Stroke: 0 mm - 110 mm

... designed to enable the use of two end-of-arm toolinggrippers(EoAT) at the same time, allowing, e.g., a RG2gripperand a RG6gripperto be used simultaneously. Our unique robot end-of-arm ...

Grip strength: 25 N - 120 N
Stroke: 0 mm - 160 mm

... designed to enable the use of two end-of-arm toolinggrippers(EoAT) at the same time, allowing, e.g., a RG2gripperand a RG6gripperto be used simultaneously. Our unique robot end-of-arm ...

... automate insertion tasks that weren’t previously possible can reduce operation costs by 40%. The RG2-FT is a state-of-the-artgripperwith added sensing and intelligence, capable of controlling the robot (on UR) and ...

Thisgripperis agripperfor large parts, in this particular case for bagged goods and pallets

... guarantee that best quality will be maintained. In addition, these adaptable parts have a wide range of uses. Thisgrippermanages two surfaces for two moulds and deals with inserts and finished parts.

This single speedgrippergrips by means of suction pads. Detection is by vacuum. Adding cylinders allows gripping on areas at an angle of more than 45°.

It is worthwhile describing various aspects of this project. Firstly, this dual-surfacegripperis able to realign itself both in the slide and in the mould. Then it picks up the finished parts and checks whether ...

Bollard grips for a wide range of samples such as yarn, fibre and thread. Bollard grips are suitable for a wide range of samples such as fibre, yarn, thread, rope, string and strapping tape. The grips are designed so that the sample ...

Eccentric roller grips for flat samples such as rubber, plastic film and paper. Eccentric roller grips are ideal for all types of flat samples such as rubber, plastic film, plastic dumbbells, paper and cardboard, sheet metal and foils. We ...

Grip strength: 60 kN

Hydraulic grips with single or double actuator. Our range of hydraulic grips cover grips with either single or double actuator. Single actuator grips have one side adjusted by manual tightening action screw. These grips are suitable ...

... Want to Pick different size objects with the same surfacegripper？考虑使用我们的止回阀系统eal unused exposed suction ports. Not accurate enough? All Area SurfaceGrippersconsists ...

... Want to Pick different size objects with the same surfacegripper？考虑使用我们的止回阀系统eal unused exposed suction ports. Not accurate enough? All Area SurfaceGrippersconsists ...

Stroke: 20 mm - 42 mm

... 3D 2nd generation External MechanicalGrippersimproves on an already great product for all your Pick N Place (PnP) bottle, jar and container needs. Engineered to use a combination of 4 to 8 gear drivengrippers...

SYSTEM RES offers a wide range of different inflatable bottlegrippers: like TGST, TGST R, TGM, TGM B , TGC, DTG , TGP models. They are used on palletizers and depalettizers which can be either automatic or semi-automatic system.

Grip strength: 10, 15, 23, 31 N

The Morali Vactec Systems has manufactured the MGgrippers, suitable for use in the plastic industry, and in various applications in the field of EOAT. These devices are equipped with a very smallgripper. ...

INCH serration Bar pulling chuck Spring actuated Clamping and positioning of short bar material Positioning of shaft type components in automatic production cycle The GF 80 is a INCH serration bar pulling chuck that is spring actuated ...

... pastry and vegetables. Food packaging Applications： •Surroundgripper, suitable for ball or square candy, pastry or fruit Food packaging Applications： •Line-fingergripper, suitable for strip, ...

Rochu Soft roboticgrippercan be used to pick the soft breathable fabric layers. pick only the first layer from multi-layers.

... parts in mobile phone, PCBs, silicon wafers, optic glasses.GripperCombination 3C-Electronics Applications： •Soft beak for micro - small parts 3C-Electronics Applications： •Grippercombination ...

Grip strength: 690 N - 3,600 N
Stroke: 3 mm - 10 mm

PNEUMATIC PARALLELGRIPPERSQPGB 3-FINGER QPGB is a universal three-finger centricgripper, with a hollow center, featuring high reliability and a long service life, suitable for applications that require ...

Grip strength: 107 N - 28,029 N
Stroke: 2 mm - 30 mm

PNEUMATIC PARALLELGRIPPERSQPG 3-FINGER QPG is a universal three-finger centricgripperfeaturing high repeatability and long service life, suitable for a wide range of industrial applications. ADVANTAGES Robust ...

Grip strength: 135 N
Stroke: 4 mm

PNEUMATIC PARALLELGRIPPERSOPL 3-FINGER OPL is a compact three-finger parallelgripperfeaturing high reliability and a long service life, suitable for handling low weight or small components. ADVANTAGES Compact ...